- Home
- Equipment
Refine by
Campbell Scientific Environmental Equipment & Supplies
114 equipment items found
Manufactured by:Campbell Scientific, Inc. based inLogan, UTAH (USA)
The 024A, manufactured by Met One, is a wind vane that measures wind direction only. You can use it in tandem with the 014A Wind Speed Sensor; however, this combination has been largely replaced by the 034B, which monitors both wind speed and wind ...
Manufactured by:Campbell Scientific, Inc. based inLogan, UTAH (USA)
The 03101 is the three-cup anemometer included with our Wind Sentry Sets. You can purchase it separately if your application requires only wind speed measurements. The 03101 connects directly to a Campbell Scientific data logger, which measures the anemometer's pulse signal and converts the signal to engineering units (mph, m/s, ...
Manufactured by:Campbell Scientific, Inc. based inLogan, UTAH (USA)
The P2546A, manufactured by WINDSENSOR, is a Class 1 anemometer often used for wind speed resource assessment and wind turbine power performance monitoring. Wind speed is sensed by a three-cup rotor assembly. Magnets mounted on the shaft cause a switch to close and open two times per revolution. Our data loggers measure the switch closure and convert the signal to engineering units (mph, m/s, ...
Manufactured by:Campbell Scientific, Inc. based inLogan, UTAH (USA)
The A100LK is an anemometer suitable for your general meteorology applications and wind-energy surveys. Its low power consumption and wide power-supply range make it popular for remote locations with no access to ac power, and its pulse/frequency signal is ideal for use with Campbell Scientific data loggers. The sensor is constructed from anodized aluminum alloys, stainless steel, and ...
Manufactured by:Campbell Scientific, Inc. based inLogan, UTAH (USA)
The 034B, manufactured by Met One, combines a three-cup anemometer and vane into a single integrated package to measure wind speed and direction. It is cabled for use with our data loggers, and it can provide you with measurements for a variety of ...
Manufactured by:Campbell Scientific, Inc. based inLogan, UTAH (USA)
The WindSonic4 is a two-dimensional ultrasonic anemometer for measuring wind direction and speed. It provides an alternative to traditional mechanical cup and vane or propeller and vane anemometers. This sonic wind sensor outputs an SDI-12 signal that can be read a a compatible Campbell Scientific data logger. (See the Compatibility section.) The WindSonic4 is not recommended for conditions where ...
Manufactured by:Campbell Scientific, Inc. based inLogan, UTAH (USA)
The 05108-45 Wind Monitor-HD is a lightweight instrument that measures wind speed and wind direction. It is designed to prevent ice buildup, allowing the sensor to provide you with accurate measurements in harsh alpine conditions that have limited accessibility. Manufactured by R. M. Young, this wind monitor is cabled for use with Campbell Scientific data ...
Manufactured by:Campbell Scientific, Inc. based inLogan, UTAH (USA)
The WindSonic1 is a two-dimensional ultrasonic anemometer for measuring wind direction and speed. It provides an alternative to traditional mechanical cup and vane or propeller and vane anemometers. This sonic wind sensor outputs an RS-232 signal that can be directly read by a compatible Campbell Scientific data logger. (See the Compatibility section.) The Windsonic1 is not recommended for ...
Manufactured by:Campbell Scientific, Inc. based inLogan, UTAH (USA)
The 107 is a rugged, accurate probe that measures temperature of air, soil, or water from -35° to +50°C. It easily interfaces with most Campbell Scientific data loggers and can be used in a variety of applications. The 107 consists of a thermistor encapsulated in an epoxy-filled aluminum housing. The housing protects the thermistor, allowing you to bury the probe in soil or submerge it in ...
Manufactured by:Campbell Scientific, Inc. based inLogan, UTAH (USA)
The 108 is a rugged, accurate probe that measures temperature of air, soil, or water from -5° to +95°C. It easily interfaces with most Campbell Scientific data loggers and can be used in a variety of applications. The 108 consists of a thermistor encapsulated in an epoxy-filled aluminum housing. The housing protects the thermistor. allowing you to bury the probe in soil or submerge it in ...
Manufactured by:Campbell Scientific, Inc. based inLogan, UTAH (USA)
The 43347-L, manufactured by R. M. Young, is a highly accurate RTD that often provides delta temperature measurements for air-quality applications. To greatly reduce radiation errors, house your 43347-L in a 43502 fan-aspirated radiation ...
Manufactured by:Campbell Scientific, Inc. based inLogan, UTAH (USA)
The CS250DM is a PT-1000 Class-A air temperature sensor for temperature gradient and stability analysis. This sensor delivers extremely accurate and precise air temperature data that is necessary for IEC 61724 Class-A solar monitoring applications and Delta Temperature (ΔT) calculations. It also includes a digital Modbus RS-485 output, ensuring data quality over long cable ...
Manufactured by:Campbell Scientific, Inc. based inLogan, UTAH (USA)
The CS456 is a pressure transducer for water-level measurements in canals, wells, ponds, harbors, lakes, streams, and tanks. It has a rugged titanium case that allows it to be used in saltwater and other harsh environments. The CS456 outputs either a digital SDI-12 or RS-232 signal to indicate observed pressure and temperature. This output can be read by many of our data loggers. The CS456 ...
Manufactured by:Campbell Scientific, Inc. based inLogan, UTAH (USA)
The NL201 is a serial-to-Ethernet interface that provides a wired Ethernet network connection to data loggers, peripherals, and other serial devices. The NL201 supports sophisticated networking capabilities for PakBus devices and networks. Using a unique technique to bridge the Ethernet and CS I/O ports, the NL201 can provide direct access to the integrated IP functionality of some Campbell ...
Manufactured by:Campbell Scientific, Inc. based inLogan, UTAH (USA)
The AM25T 25-Channel Solid State Multiplexer increases the number of thermocouples that you can measure using a Campbell Scientific data logger. The multiplexer interfaces with the data logger and adds terminals so that you can wire additional thermocouples or other low-level voltage output ...
Manufactured by:Campbell Scientific, Inc. based inLogan, UTAH (USA)
The SkyVUE™PRO LIDAR ceilometer measures cloud height and vertical visibility for meteorological and aviation applications and is ideal for long-term research applications where a high level of detail is required. Its robust construction is ideal for long-term installation, as it requires minimal maintenance and features a unique stratocumulus calibration procedure—allowing the ...
Manufactured by:Campbell Scientific, Inc. based inLogan, UTAH (USA)
The AL205B is an ALERT2 receiver that is configured to support receiving ALERT2 messages typically used at base stations. The AL205B is configured with a radio receiver. Three serial ports allow for input and output to several devices including a data logger, PC, and serial media converters. Local and remote data collection and administration are possible through the micro USB console and ...
Manufactured by:Campbell Scientific, Inc. based inLogan, UTAH (USA)
The ALERT205 is the easiest ALERT2 transmitter to use on the market, and its additional communications options and variety of form factors make it flexible to fit the needs of your application. The ALERT205 is available in canister, enclosure, and backplate form factors—offering you a variety of compatible installation methods. In addition, as the heart of any ALERT2 or flood warning ...
Manufactured by:Campbell Scientific, Inc. based inLogan, UTAH (USA)
With an AVW200 vibrating-wire analyzer module, your data logger can measure vibrating-wire strain gages, pressure transducers, piezometers, tiltmeters, crackmeters, and load cells. These sensors are used in a wide variety of structural, hydrological, and geotechnical applications because of their stability, accuracy, and durability. The VSPECT technology is protected under U.S. Patent No. ...
Manufactured by:Campbell Scientific, Inc. based inLogan, UTAH (USA)
The AVW216 is a vibrating-wire analyzer module that includes an internal 2.4 GHz spread-spectrum radio for wireless communication in many countries worldwide. With this vibrating-wire analyzer module, your data logger can measure vibrating-wire strain gages, pressure transducers, piezometers, tiltmeters, crackmeters, and load cells. These sensors are used in a wide variety of structural, ...